Dynamic Engineering - www.dyneng.com
Order Cables
Order Chassis
Carriers Adapters Converters
Order cPCI
Dynamic Engineering Product Pages
Order IndustryPack Modules
Order Misc.
Order PCI
Order PCI-X
Order PCIe
Order PMC
PC104 PCI104 PC104p
View Cart

Order Misc.

DINterm64_f_sm.jpg DinTerm64
DINterm64 provides a space efficient, low cost method of interconnecting the control electronics to the rest of the sensors, IO, machinery etc.

HDEcable-2x1.jpg HDEcabl68
SCSI II/III cable - 68 pin high density SCSI connectors with latch blocks or 2-56 thumbscrew hardware in 3 ft. and 6 ft. lengths. Twisted pair construction. Use with PMC hardware such as Dynamic Engineering's PMC-Parallel-TTL etc.

Please select cable version below.
LB = Latch block (default)
TS = ThumbScrew
SCSI II/III to 68 screw Terminal positions [standard]. SCSI II/III adapter to terminal strip. Custom termination options. Horizontal, Vertical and mixed connector options. Fully enclosed [with DIN rail mounting], open and engineering models available.

Please choose from the menus
hde100cablesm.jpg HDECable100
D100 Cable with 50 twisted pairs. Latch Block or Thumbscrew mating. Shielded and outer jacket. 3' and 6' standard plus custom lengths.

HDEterm100sm.jpg HDEterm100
D100 to 100 Terminal positions

Please select from below if you wish to have a special version
HDRribn50sm.jpg HDRribn50
50 pin ribbon cable with connectors, strain relief and pull tabs. Many lengths stocked, custom lengths are easy to order. Standard Female connectors and flat ribbon cable. Male / Female mixed connectors and twisted pair available.

Ribbon cable to terminal strip adapter / converter. 50 position header with ejectors to connect to ribbon cable and 50 screw terminals in a flow through layout. Din rail compatible housing. Option for engineering version without screw terminals and header strip instead- suitable for scope, loop-back etc.

Ordering Options:
Use IP-Connector-Saver to increase the space between the IP Module and Carrier. IP-Connector-Saver can also be used to save wear on the Carrier or IndustryPack connectors when in a test or T&I environment. Good when additional air flow is required for a hot module. Sold in pairs. Adds ~.534" to the standard height of .472".
PCI Riser Card
PCI Riser Card

PCI2cPCI-32 Install a cPCI board into a PCI slot. This adapter supports 32-bit cPCI bus. Usually used with a 3U cPCI board. 6U devices can be used when the upper half of the PCI bus is not required. Supports all PCI modes including Target, Master, DMA, interrupts etc. Passive design with impedance controlled traces between PCI and cPCI connectors.
PCI2cPCI-64.jpg PCI2cPCI-64
PCI2cPCI-64 Install a cPCI board into a PCI slot. This adapter supports 64-bit

pmc2pci_f_sm.jpg PMC2PCI
Adapter/carrier card mounts in a PMC slot and provides a PCI slot.

Please Select Ordering Options:
Dynamic Engineering SpaceWire Break-Out (DESWBO) Install between two SpaceWire nodes and monitor the signals between the two nodes. 24 test points per node [48 total], Credit/Byte count, decoded data, decoded characters NULL, FCT, Timecode received, EOP, EEOP, Credit Error, Disconnect Error, Escape Error, Parity Error. Activity LED's. International Power Supply included.
IP Crypto
IP-Crypto is a special version of IP-Parallel-HV. The basic design features are retained, and an interface to a KYK-13 is provided. 6.5V reference output, transfer request output, and 3 inputs for clock, data and switch. Alternate voltage references are available. For example 5.85V [newer KYK models] is an option. The rest of the 24 Input and Output IO are available as a parallel port.
Use your PCI-104 or PC/104p board in a standard PC. Two orientations supported for Production and Test. Note: only PCI interface is supported. ISA connector has mounting mounts only. In the Production position, the PCI-104/PC104p card is mounted completely within the framework of the PCI adapter. With the Test orientation the PCI-104 card is rotated to be above the PCI adapter allowing access to both sides of the device and better access within a chassis. The test version has test points installed on the PCI signals.

Please select version from below:
DINribn64_f_sm.jpg DINribn64
DINribn64 is designed to interconnect devices using 64 connection DIN connectors. Rows A and C are utilized. Many Dynamic Engineering products have this connector system as well as products from third parties for VME systems. Utilize DINribn64 cable to connect the DINterm64 to PCIeBPMCX1, PCIBPMC, PCIeBPMCX2, PCI2PMC etc. A snap together breakout system with DIN rail capability is created with these components. You can also use the DINribn64 to interconnect your rear IO VME hardware to the DINterm64 or other breakout device.
SpaceWire cable available in standard and custom lengths. Multiple options for connectors and wiring. Standard SpaceWire - male:male with TX/RX reversal. Contact the factory for other options or go to the SpaceWire cable page http://www.dyneng.com/SpaceWireCable.html