Dynamic Engineering - www.dyneng.com
Carriers Adapters Converters
Dynamic Engineering Product Pages
Order Cables
Order Chassis
Order cPCI
Order IndustryPack Modules
Order Misc.
Order PCI
Order PCI-X
Order PCIe
Order PMC
PC104 PCI104 PC104p
View Cart
     

Order PCI

 
Cable-MDM9-Spacewire
SpaceWire cable available in stock and custom lengths. Multiple options for connectors and wiring. Standard SpaceWire - male:male with TX/RX reversal. Contact the factory for other options or go to the SpaceWire cable page http://www.dyneng.com/SpaceWireCable.html


Quantity
 
DESWBO
Dynamic Engineering SpaceWire Break-Out (DESWBO) Install between two SpaceWire nodes and monitor the signals between the two nodes. 24 test points per node [48 total], Credit/Byte count, decoded data, decoded characters NULL, FCT, Timecode received, EOP, EEOP, Credit Error, Disconnect Error, Escape Error, Parity Error. Activity LED's. International Power Supply included.
Quantity
 
hde100cablesm.jpg HDECable100
D100 Cable with 50 twisted pairs. Latch Block or Thumbscrew mating. Shielded and outer jacket. 3' and 6' standard plus custom lengths.

Quantity
 
HDEterm100sm.jpg HDEterm100
D100 to 100 Terminal positions




Please select from below if you wish to have a special version
Quantity
 
HDRterm50
Ribbon cable to terminal strip adapter / converter. 50 position header with ejectors to connect to ribbon cable and 50 screw terminals in a flow through layout. Din rail compatible housing. Option for engineering version without screw terminals and header strip instead- suitable for scope, loop-back etc.

Ordering Options:
Quantity
 
PCI Riser Card
PCI Riser Card


Quantity
 
pcialtera485_sm.jpg PCI-Altera
PCI card with 20K400 or other footprint compatible device, plus 40 RS485 channels, and 12 TTL IO.
Altera is loaded via PCI bus, JTAG or PROM. 16 - 4K x 8 FIFOs between Altera and Xilinx FPGAs to allow for rate matching.
DMA on PCI bus with PLX 9054.



To include a Driver and/or Engineering kit w/order select Please select card version: 485, LVDS, mixed
Quantity
 
pci_harpoon_f_sm.jpg PCI-Harpoon
Please select engineering kit/Driver options below:
Quantity
 
lvdscable2x1.jpg PCI-LVDS-Cable
100 position, .050 MDR/MDR for high speed digital data transmission systems.
Quantity
 
pci_serial_ecl_sm.jpg PCI-NECL-ASN1
High speed DMA supported ECL IO



To include a Driver and/or Engineering kit w/order select
Quantity
 
PCI-Spacewire
PCI card with 4 independent SpaceWire Interface nodes. Drivers, reference software, cables, bus debugging tools and support available. K and BK models with options for added memory. Up to 200 MHz operation. Linux, Windows, VxWorks



Please select Engineering kit, driver and Development tool options below:
Quantity
 
PCI2cPCI
PCI2cPCI Install a cPCI board into a PCI slot. Supports all PCI modes including Target, Master, DMA, interrupts etc. -32 supports 32 bit PCI connection. -64 supports 64 bit PCI connection. -32-IO supports 32 bit PCI and rear IO from the cPCI module.

Passive design with impedance controlled traces between PCI and cPCI connectors.
Quantity
 
PCI2cPCI-32
PCI2cPCI-32 Install a cPCI board into a PCI slot. This adapter supports 32-bit cPCI bus. Usually used with a 3U cPCI board. 6U devices can be used when the upper half of the PCI bus is not required. Supports all PCI modes including Target, Master, DMA, interrupts etc. Passive design with impedance controlled traces between PCI and cPCI connectors.
Quantity
 
PCI2cPCI-64.jpg PCI2cPCI-64
PCI2cPCI-64 Install a cPCI board into a PCI slot. This adapter supports 64-bit


Quantity
 
PCI2PC104p
Use your PCI-104 or PC/104p board in a standard PC. Two orientations supported for Production and Test. Note: only PCI interface is supported. ISA connector has mounting mounts only. In the Production position, the PCI-104/PC104p card is mounted completely within the framework of the PCI adapter. With the Test orientation the PCI-104 card is rotated to be above the PCI adapter allowing access to both sides of the device and better access within a chassis. The test version has test points installed on the PCI signals.

Please select version from below:
Quantity
 
PCI2PMC
1/2 length PCI adapter carrier card with PMC mounting slot. Front panel and Pn4 IO access. 32 / 64 bit operation.




If you wish to order a version other than the standard PCI2PMC, please select from below.
Quantity
 
PCI3IP
Industrial temperature 1/2 size PCI card with 3 Industrypack compatible positions. single and double wide IP's. 8 and 32 MHz selection per IP Module. 32 bit accesses to IP's supported. Fused filtered power to each position. Integrated PCI <=>IP bridge function. Automatic 32 bit to IP conversion.




To include a Hardware Engineering kit with your order select from below.
Quantity
 
PCI5IP
PCI5IP is a full length universal voltage signaling PCI card with 5 IP positions. 8 or 32 MHz operation in each IP position. 32 to 16 bit conversion, fused filtered power, Windows and Linux support.

To include a Driver with your order please select from below.
Quantity
 
pcibpc104p-et_f_sm.jpg PCIBPC104p-ET
Use your PC/104p boards in a standard PC. Two orientations supported for production mode and test.
Quantity
 
PCIBPMC
1/2 length Bridge Based PCI adapter carrier card with PMC mounting slot. 32/33 <=> 64/66 operation on PCI and PMC buses. Local power supply for 3.3V to PMC with option for backplane supply or local supply to be used. Options for adding Ethernet and Serial ports to use with PrPMC's. Options for Zero Slot Fans in either or both positions. Both legal for PMC and PCI mechanical requirements. Pn4 IO supported with a DIN rows A&C filled connector. Option for SCSI connector. Option for JTAG support. PCIBPMC: Order for a base version PCIBPMC-ROHS: ROHS processed card PCIBPMC-SCSI: Order for a SCSI Connector version PCIBPMC_RJ45&Ser: with Serial & Ethernet PCIBPMC-VIO3 PCIBPMC-SCSI-VIO3:; PCIBPMC-ENET-VIO3: with 2 ethernet ports, 3.3V PCIBPMC-SER-VIO3: with serial con 3.3V PCIBPMC-Customized: We cater to our customers special orders - please email your requirements for a PCIBPMC with modifications to meet your needs dedra@dyneng.com PCIBPMC Fan Options: PCIBPMC-FAN1 closest to the PCI bezel PCIBPMC-FAN2 closest to the PMC Connectors

Ordering Options: Please select the board version and engineering kit you wish to order.
Quantity
 
PCIbPMC-ET-f_sm.jpg PCIBPMC-ET
Ordering Options: Please select the board version and engineering kit you wish to order.
Quantity
 
pcibpmcx1_f_sm.jpg PCIBPMCx1
The PCIBPMCX1 provides the ability to install one PMC card into a standard PCI/PCI-X slot. Programmable 3.3 or 5V




Ordering Options: Please select the board version and engineering kit you wish to order.
Quantity
 
pcibpmcx2_sm_f.jpg PCIBPMCx2
PCIBPMCx2 PCI/PCI-X & PMC Compatible Adapter Carrier with 2 PMC positions. ROHS or Std processing. Optional FAN's, type of rear IO connector.



Ordering Options: Please select the board options you wish to order.
Quantity
 
pmc2pci_f_sm.jpg PMC2PCI
Adapter/carrier card mounts in a PMC slot and provides a PCI slot.




Please Select Ordering Options:
Quantity