PMC-MC-X2-RIO

PMC-MC-X2-RIO adapter, carrier, motherboard provides the ability to install up to 2 (two) PMC modules into a small enclosure. PMC-MC-X2-RIO has one PMC card positions top and bottom to create a compact arrangement with 2 PMC positions. X2 is a complete solution with built in power supplies, thermal protection, voltage monitoring, bus arbitration, clock distribution, fan control and more. Compact chassis available to house PMC-MC-X2-RIO.

Referenced to 10-40V " expanded 28V" range PMC-MC-X2-RIO provides power supplies for +5, +3.3, +12, and minus 12. The 12V supply is buck-boost to allow operating at voltages below 12V and still have 12V regulated power. The standard "Power Din 4" connector is used for the input to the X4 when using the PMC-MC-X2-RIO Chassis. For embedding into your equipment the optional Molex vertical connector is recommended. With the chassis version, a wall mount transformer supply is provided. With the "RIO" version, the input power reference is used to generate the 2 PMC rails directly. The 3.3 and 5V supplies can source 15A. The +12V and -12V are 4A supplies [pin limited by the PMC devices]. The -12V can be disabled via the dipswitch if not used in your design.

PCI VIO is programmable allowing 5V or 3.3V PMCs to be used. The voltage select pins are not installed [the keying holes are provided] on PMC-MC-X2-RIO. Many PMCs are "universal" and can work with 3.3 or 5V PCI backplanes. The DIPSWITCH selects 5V or 3V operation. The Silk-Screen incorporates a legend with the DIP switch options.

The PCI bus is suitable for 32 and 64 bit operation at PCI and PCI-X speeds. 25-133 MHz. Each of the slots including Slot 0 has a request and grant connection to the arbiter located within the CPLD. Interrupts are routed from Slots 1, 2, and 3 to slot 0. IDSEL address range is selectable via the DIPSWITCH. Reset is based on supervisor circuits checking that the 3.3V and 5V rails are valid or the reset option from the DIPSWITCH. Slots 0,1,2 and 3 are clearly marked in the silk-screen.

PrPMCs frequently have concentrated power consumption requiring air flow for proper cooling. The larger load also puts a thermal load on the PMC-MC-X2-RIO components. The X2 was designed to accomodate convection cooling. The slots in the side of the PMC-MC-X2-RIO design are for fans. [Please refer to the pictures above.] PMC-MC-X2-RIO has temperature controlled power [+12V] for fans. The -RIO model has 40 mm 12V fan cutouts for improved sound levels.

The PMC-MC-X2-RIO Chassis comes with twin fans making use of the cutouts. The X2 chassis comes with grids on both sides to provide for proper air flow across the PMCs and PMC-MC-X2-RIO. Please refer to the picture of the open X2 chassis toward the bottom of the PMC-MC-X2-RIO-Chassis page.

Pn4 IO from each PMC position is routed to VHDCI connectors mounted to the rear of PMC-MC-X2-RIO. Matched length [.001"], impedance controlled differential routing is provided. Please see the manual for the connection definitions. The shield on each of the VHDCI connectors can be AC, DC or open coupled to ground for the cable shield reference. A header is provided to make the selection.

The original PMC-MC-X2 is available to support projects already through T&I. PMC-MC-X2-RIO is recommended for new designs. Please note: PMC-MC-X2 and PMC-MC-X2-RIO have different mounting points and are not interchangeable unless this is taken into account.

If you have custom requirements please call or e-mail us with the details.
email us your wish list or call today